DASH1 Display unit
The DASH1 is a compact, robust, water resistant data
display system for use with our range of data logging
products. Once the DASH1 is connected to one of our data
loggers, it can be configured to display many key parameters
including real time lap and sector times calculated from GPS
data, any available analogue measurements (e.g. temperatures
and pressures), RPM, wheel/shaft speeds etc. The actual data
displayed can be set up for the users specific requirements.
You can also set independent alarms for all channels.
Who is the DASH1 designed for?
The DASH1 can be used for road, racing and development
applications. It extends the use of our loggers by allowing
the user to see the data in real time in the vehicle. The
DASH1 is very robust, making it ideal for demanding
applications from single seaters to a professional
engineering environment.
What does the DASH1 do?
The DASH1 accepts the serial data stream from our range
of data logging products converts them to the users
preferred units and displays them on the screen. For example
you could display exhaust gas temperature or oil pressure,
you can also set warning levels for each channel to indicate
when an input is too high or low. Crucially, the DASH1 also
displays high accuracy lap and sector times, calculated from
GPS data without the need for a trackside beacon. The actual
data that the DASH1 displays, as well as the units etc can
all be configured from a PC to the users exact requirements.
Up to 30 different user defined screens can be set up.
Depending on the device that the DASH1 is connected to the
following channels are available for display:
| |
DL2 |
DL1 |
AX22 |
SPEEDBOX |
| GPS-based lap and sector times
|
Yes |
Yes |
Yes |
- |
|
Accelerations |
Yes |
Yes |
Yes |
Yes |
|
RPM |
Yes |
Yes |
Yes |
- |
|
Analogue channels (pressures,
temperatures, etc) |
16 |
8 |
- |
- |
|
Frequency channels |
4 |
4 |
- |
- |
|
Speed |
Yes |
Yes |
Yes |
Yes |
|
Position/altitude |
Yes |
Yes |
Yes |
Yes |
DASH1 features
- Anodised aluminium CNC machined case, sealed to IP65
- Large, clear, backlit 40 character display
(characters approximately 10mm high)
- 4 large 15mm buttons, for easy operation even with
gloves
- Single 9 way d-type to accept power and serial data
(leads available for AX22, DL1, DL2, SPEEDBOX)
- Configurable from a PC
- 5 user configurable screens with values, bar graphs,
or both
- Real time lap and sector times without a
track side optical beacon
- Robust, billet aluminium enclosure, sealed
to IP65
- User configurable display, 5 screens of data
- Compatible with the DL2, DL1, AX22 and
SPEEDBOX products
| Display |
40 Character, backlit
display, character height 9.85mm |
|
Controls |
4 off 15mm buttons embedded
into custom made front panel |
Power
Supply
Requirements |
12v nominal input, minimum
of 10v, maximum of 15v. Current consumption
of about 180mA. |
| Case
Construction |
CNC machined aluminium. |
| Connector
Type |
Very high reliability, IP65
9 way d-type |
|
Main Processor |
RISC with embedded flash
program memory |
| Serial Port |
Auto speed for receiving
information in a standardised serial stream
from our data logging products. Also used
for re-flashing, diagnostics and
configuration. |
| Temperature
Limits |
Factory |
|
DASH1 configuration
The data that is displayed can be configured using the PC
software provided, meaning that only the relevant data is
visible and presented in the most helpful format. Using the
configuration software you can control:
- Which channels are displayed
- The name of the channels
- The units displayed
- The scaling of the channels
- The number of decimal places displayed
- Whether 2, 3 or 4 channels are displayed on the
screen
- Whether the channel is displayed as a value or bar
graph
- The lower and upper warning levels for the channels
The actual information available for display depends on
the hardware that the DASH1 is connected to, as shown in the
table above.
List Pricing:
DASH1 $675.00
To place an order please Contact Us
Ask about our 10% Holiday Discount!
|
